Updates Caro®+

The control panel is used to operate the control unit and control the antenna.

Production year ∼ 2004 − 2006

Unfortunately, a software update is no longer available for this version as support has been discontinued.

Please contact ten Haaft: +49 (0) 7231 58 588 0

Operator panel with integrated control unit

Production year ∼ 2006 − June 2015

Software update via USB stick

The software of the new control panels of generation V5 (since November 2016) can be updated via USB stick.

Important note:
Before updating the software, be sure to carefully read the corresponding description. Please follow the instructions carefully as otherwise the function of the system may be impaired.

Download of the description 'Updates via USB stick'
Download of the firmware for the Vision II control unit (2.62 - 13.02.2018)

Software update via SD card

The new control panel (from March 2011) will permit a software update via SD card.

Important note:
Please read the respective description carefully before performing software updates. Please follow the instructions precisely as non-compliance could result in functional defects of the system.

Download the Description Update via SD-Card
Download the firmware for the control unit Vision II (2.62 - 13.02.2018)

Software update via computer

For control units with older operator panels (∼ 2006 - February 2011), a software update can be preformed by qualified personnel via computer.

Please contact ten Haaft if you have further questions: +49 (0) 7231 58 588 0

Operator panel V5 and control unit

New operator panel and control unit

Old operator panel and control unit

Production year from ∼ June 2015

Software update via USB stick

The software of the new control panels of generation V5 (since November 2016) can be updated via USB stick.

Important note:
Before updating the software, be sure to carefully read the corresponding description. Please follow the instructions carefully as otherwise the function of the system may be impaired.

Download of the description 'Updates via USB stick'
Download of the firmware for the Vision III control unit (3.59 - 13.02.2018)

Software update via SD card

Important note:
Please read the respective description carefully before performing software updates. Please follow the instructions precisely as non-compliance could result in functional defects of the system.

Download the Description Update via SD-Card
Download the firmware for the control unit Vision III (3.59 - 13.02.2018)

Please contact ten Haaft if you have further questions: +49 (0) 7231 58 588 0

Operator panel V5 and control unit

Operator panel and control unit

Software update via USB-Stick

The control panel can also be updated via a USB stick. This requires the USB stick with a specific container file (UF file) to be plugged into the USB port before switching the system on:

1. Disconnect the control panel from the control unit (i.e. disconnect it from power supply).
2. Copy file "ctrlbox.uf" to an empty USB stick.
3. Plug the USB stick into the control panel using an adapter.
4. Connect the control panel to the control unit (i.e. restore power supply)
5. The update of the control panel will start automatically. The whole procedure does not take longer than 15 seconds.
6. The control panel will then reboot and verify the firmware. The USB stick can then be removed.
7. Done!

Download the Firmware for control unit V5 (1.15 - 773850 - 21.06.2017)

Control unit V5

Production year from ~ 2003 − 2006

Receiver characteristic: among others 2 x Scart sockets

Software update via computer

Important note:
Please read the respective description carefully before performing software updates. Please follow the instructions precisely as non-compliance could result in functional defects of the receiver.

Download the Description Update with TERA TERM
Download the update programm Tera Term
For this version of receiver the support was discontinued, you can find the last available software version at the following link:
Download channel list and receiver firmware Caro (19.04.2013)

Please contact ten Haaft if you have further questions: +49 (0) 7231 58 588 0

Receiver CARO FTA

Receiver CARO CI

Digital receiver S7 / S8 (silver)

Production year from ~ 2007 − 2014

Receiver characteristic: among others 1 x Scart socket

Software update via satellite (from 2008)

Follow our instructions and update your software step by step via satellite.

Downlaod the Description for Update via Satellite

Software update via computer

Important note:
Please read the respective description carefully before performing software updates. Please follow the instructions precisely as non-compliance could result in functional defects of the receiver.

Download the Description Update with TERA TERM
Download update programm Tera Term
Download channel list and receiver firmware (TH_220U - 08.02.2018)

Please contact ten Haaft if you have further questions: +49 (0) 7231 58 588 0

Digital receiver S7

Digital receiver S8

HD receiver „Europe“ (black)

Production year from ~ 2013

Receiver characteristic: no Scart socket, among others digital HDMI socket

Softwareupdate via USB flash / SD card

Important note:
Please read the respective description carefully before performing software updates. Please follow the instructions precisely as non-compliance could result in functional defects of the receiver.

Download the Description for the HD Europe Receiver Update
Download firmware and channel list (EU//3.45 - 18.04.2018)

Please contact ten Haaft if you have further questions: +49 (0) 7231 58 588 0